少妇高潮一区二区三区99,亚洲av无码av日韩av网站,亚洲成AV人片在线观看WW,国产精品jizz在线观看老狼

網站首頁技術中心 > CD-800 Dicing Machine               Instruction
產品目錄
CD-800 Dicing Machine               Instruction
更新時間:2013-07-29 點擊量:3611

This type of machine is specialized in vegetable and cormcutting. It is easily operating for woman. It is also the necessary facility for restaurants and second processing factories. Instantaneous ability is above 15 people. This machine will let you have satisfied feeling.

 

A.   Processing material

    Potatoes, carrots, melons, bamboos, onions, apples, vegetables and so on.

 

B. Processing dimension:

(standard)

               H                 10. 15. 20mm cubes or bars.

L              T            (special dimension)

                             3-20mm cubes or bars.

 

C. Capacity

15/mm cubes;    1000kg/hr

 

D.   Voltage

3 phase / 415V, 50Hz / 4P / 0.75KW

(each countries has different voltage connection)

E.   Machine dimension & weight

L 800×W 700×H 1260mm

 

F. Cutting work outline

    Connecting “ON” switch, add little water when machine is running and put suitable amount of material to the machine. (Material diameter under 8/cm). Leaf blade will turn over the material to the fixed thickness of the place of flate cutter. And crosscut cutter will cut the bars into cubes and flow down to the machine after round cutter cuts material into bars. Easily operate, and processing material is clean and delicacy.

 

 

 

 

 

 

 

 

 

 

 

G. Voltage connection

    Power: 3 phase / 415V / 4P / 0.75KW. Connect power cord (red, black, white) when use the machine. Then connect (green) line to insurance after that start to operating.

 B

 

 

 

 

 

               A

 

(1) The power line A connected to power supply. (Attention the    motor shift)

(Attention 4 power lines, green for the grounding line.)

(2) Water pipeline will be connected B, then the installation is completed.

 

 

 

H.   Installing location

    Consider whether the water drains unimpededly or not when install the machine.

 

I.   Watch out the machine running

    Make sure there are no foreign objects on the entrance of the machine and inside of the leaf blade after connecting voltage to avoid the cutter broken while the machine running. Make sure the direction of leaf blade is correct, rith circum gyratoin (clock-wise).

 

J. Method of adjusting thickness of flate cutting

The standard allocation method as follows: (if cut cube is formed by three Cutter)

(1) The first knife (cutting thickness): Plane broadswords Z.     (Adjustable by cutting thickness)

(2)   The second knife (cutting width): Circular knife Group Y.

  5mmP (space): 5mm

 10mmP (space): 10mm

 15mmP (space): 15mm

 20mmP (space): 20mm

 

(3)   The third knife (cut length): transverse plane knife Group.

5mm uses 15 knife group

10mm uses 8 knife group

15mm uses 6 knife group

20mm uses 4 knife group

 

K.   Method of adjusting aluminum fence

Aluminum fence feeds material to crosscut cutter when round cutter cuts the material. This is why the sharp place of aluminum fence has to get close to the cushion of gap of round cutter or the dimension of aluminum fence marks on the bottom right side.

 

L. Round cutter discharging

Round cutter dimension drawing

Round cutter dimension

 

 

Standard (mm)

P: 10

P: 15

P: 20

Special (mm)

P: 3-20

(1) Avert black screw of fixed eccentric axis.

(2) Pull down the fixed bolt of round cutter eccentric axis. Then round cutter can be discharged.

(3) Fix the u-shape spanner on the round cutter set, then loosen sexangular on the round cutter axis (two sides of 24m/m spanner), then it can be taken out.

 

 

 

M. Crosscut cutter discharge

Crosscut cubes round piece

5m/m uses 21 pieces

10m/m uses 8 pieces

15m/m uses 6 pieces

20m/m uses 4 pieces

(1) Fix u-shape spanner on the fixed crosscut cutter set when discharge crosscut cutter. Then loosen sexangular screw (24m/m spanner), then it can be taken out.

 

N. Daily cleansing

    Clean the machine after finish the jobs. Run the machine while operating, then wash it by flush water to clean the leavings.

O.   Standard by-products:

Spanner         10, 19, 24………….3

Screwdriver (-), (+)……….……………2

U-shape spanner                 1 PCS

Lubricant oil                    1

Tool box                       1 box

中文在线 | 中文| 欧美人与动牲交xxxxbbbb| 精品人妻一区二区三区四区在线| 国产成人AV区一区二区三| 欧美激情xxxx性bbbb| 777色婷婷AV一区二区三| 国产98色在线 | 国| 久久久久AV综合网成人| 四川少妇bbw搡bbbb槡bbbb| 亚洲欧洲精品无码av| 久久aⅴ无码av高潮av喷吹| 久久久久无码中| 少妇伦子伦精品无码| 精品性高朝久久久久久久| 最近的2019中文字幕国语在线| 国产精品岛国久久久久| 国外AV无码精品国产精品| 国产人成视频在线观看| 国产人妻久久精品二区三区特黄| 亚洲成av人片一区二区三区| 亚洲精品成人片在线观看| 亚洲精品中文字幕无码蜜桃| 黄页网址大全免费观看| 成av人片一区二区三区久久| 荫蒂每天被三个男人添视频| 国产在线精品一区二区三区不卡| 一本色道久久综合亚洲精| 国产精品成人一区二区三区| 无码任你躁久久久久久老妇| 免费B站在线观看人数在哪儿找| 少妇被多人c夜夜爽爽av| 久久99精品久久只有精品| 天黑黑影院在线观看视频高清免费 | 色偷拍 自怕 亚洲 10p| 欧美人与动交zozo| 无套内谢少妇毛片a片软件| 亚洲色偷偷色噜噜狠狠99网| 亚洲精品久久久久久久蜜桃| 国内精品久久久久伊人av| 国产伦孑沙发午休精品| 又大又长粗又爽又黄少妇视频|